NZQA EXPIRING UNIT STANDARD 2908 VERSION 8 PAGE 2

NZQA EXPIRING UNIT STANDARD 101 VERSION 8 PAGE 3
NZQA EXPIRING UNIT STANDARD 10532 VERSION 5 PAGE 3
NZQA EXPIRING UNIT STANDARD 1117 VERSION 6 PAGE 4

NZQA EXPIRING UNIT STANDARD 1120 VERSION 6 PAGE 2
NZQA EXPIRING UNIT STANDARD 11281 VERSION 6 PAGE 3
NZQA EXPIRING UNIT STANDARD 11582 VERSION 6 PAGE 4

2908 Perform quality tests on fabric

NZQA Expiring unit standard	2908 version 8
	Page 2 of 2

Title	Perform quality tests on fabric
Level	3	Credits	5

Purpose

This unit standard is for people working in the weaving industry. People credited with this unit standard are able to: describe woven fabric tests and the reason for each test; take samples and carry out tests on fabric to determine construction and quality characteristics; and analyse and report test results.

Classification

Textiles Manufacture > Weaving

Available grade

Achieved

Guidance Information

Plant safety practices comply with Health and Safety in Employment Act 1992 and workplace procedures.

Outcomes and performance criteria

Outcome 1

Demonstrate knowledge of woven fabric tests and reasons for testing.

Range picks and ends per cm, fabric weight, abrasion resistance, colour fastness to wet and dry rubbing, colour fastness to light, seam slippage, extractable matter, acid and water repellency, breaking load, burst strength, shrinkage, seam slippage.

Performance criteria

1.1 Test procedure and reasons for carrying out the test are described.

1.2 Calculations required by the test are carried out according to the test method.

Outcome 2

Sample and test woven fabric.

Range picks and ends per cm, fabric weight, abrasion resistance, colour fastness to wet and dry rubbing and any 3 other tests from the range of Outcome 1.

Performance criteria

2.1 Frequency and timing of sample is according to operating procedure.

2.2 Sample is taken and handled according to test method.

Range selection, holding conditions, sub-sampling.

2.3 Test procedure is carried out according to test method.

Range equipment assembled, conditioning requirements, test technique.

2.4 Results are recorded according to workplace requirement.

Outcome 3

Analyse and report on test results.

Range picks and ends per cm, fabric weight, abrasion resistance, colour fastness to wet and dry rubbing and any three other tests from the range of Outcome 1.

Performance criteria

3.1 Test sample variables are calculated according to the test method.

3.2 Results are studied and compared with plant standards to assess conformance to standard.

3.3 Deviations from plant standard are reported to the designated plant staff and according to plant procedure.

3.4 Test records, results and reports are kept according to plant procedure.

This unit standard is expiring. Assessment against the standard must take place by the last date for assessment set out below.

Status information and last date for assessment for superseded versions

Process	Version	Date	Last Date for Assessment
Registration	1	3 April 1995	31 December 2022
Revision	2	8 August 1997	31 December 2022
Revision	3	18 July 2000	31 December 2022
Revision	4	10 October 2001	31 December 2022
Revision	5	12 August 2004	31 December 2022
Rollover	6	25 July 2007	31 December 2022
Rollover	7	21 May 2010	31 December 2022
Review	8	30 September 2021	31 December 2022

Consent and Moderation Requirements (CMR) reference

0030

This CMR can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.

Competenz

SSB Code 101571

Ó New Zealand Qualifications Authority 2021

NZQA EXPIRING UNIT STANDARD 11633 VERSION 6 PAGE 3
NZQA EXPIRING UNIT STANDARD 11635 VERSION 6 PAGE 3
NZQA EXPIRING UNIT STANDARD 11731 VERSION 4 PAGE 4

Tags: expiring unit, version, standard, expiring