HP Laserjet 5000 Series Maintenance Kit Installation Instructions C4110-69006
Alternate kit part number: C4110-67914
For HP laserjets 5000, 5000N, 5000DN, 5000GN, Hewlett Packard recommends the installation of a maintenance kit after every 150,000 pages printed. This is a rough estimate and you may need to install a maintenance kit far sooner than that depending on printing conditions and if the printer has been previously serviced with low quality aftermarket parts.
To purchase an HP Laserjet 5000 maintenance kit click here.
A picture is worth a thousand words...It's a lot easier to show somebody how to install a maintenance kit than to tell them. After talking with hundreds of customers over the phone about installing printer maintenance kits we decided to write our own manuals. The instructions we found from Hewlett Packard and other sources were missing lots of information and often didn't contain any pictures. So here you are! We hope you find the installation instructions helpful. A lot of time went into creating them, feel free to email us with your comments!
Contents
What is included in a Laserjet 5000 maintenance kit?
Fuser installation.
Transfer roller installation.
Tray 1 (Multi-purpose tray) pick-up roller and separation pad.
250 sheet tray pick-up rollers and separation pad.
500 sheet tray pick-up and separation rollers.
What is included in a Laserjet 5000 maintenance kit?
Qty. |
Description |
1 |
HP laserjet 5000 fuser (RG5-5455) |
1 |
Transfer roller OEM (RG5-3579) |
1 |
Manual feed tray separation pad OEM (RF5-3439) |
1 |
Manual feed tray pick-up roller OEM (RB2-1820) |
1 |
Tray 2 (250 sheet tray) pickup roller OEM (RB2-1821) |
1 |
Tray 2 (250 sheet tray) separation pad OEM (RG9-1485) |
4 |
500 sheet tray pick-up rollers OEM (RB1-8865) |
2 |
500 sheet tray feed and separation rollers OEM (RF5-2634) |
Note: All of our maintenance kits include Hewlett Packard (OEM) rollers, not cheap aftermarket rollers. This increases the cost of the kit but in the long run your parts will last longer and you will spend less time on expensive service calls.
Click here for more information about aftermarket vs. OEM rollers.
Images |
|
|
Description |
Qty in kit |
HP laserjet 5000 fuser (RG5-5455) |
1 |
|
Transfer roller OEM (RG5-3579) |
1 |
|
|
Manual feed tray separation pad OEM (RF5-3439) |
1 |
|
Manual feed tray pick-up roller OEM (RB2-1820) |
1 |
|
Tray
2 (250 sheet tray) pickup roller OEM |
1 |
|
Tray
2 (250 sheet tray) separation pad OEM |
1 |
|
500 sheet tray pick-up rollers OEM (RB1-8865) |
4 |
|
500
sheet tray feed and separation rollers OEM |
2 |
To purchase an HP Laserjet 5000 maintenance kit click here.
For HP laserjets 5000, 5000N, 5000DN, 5000GN, Hewlett Packard recommends the installation of a maintenance kit after every 150,000 pages printed. This is a rough estimate and you may need to install a maintenance kit far sooner than that depending on printing conditions and if the printer has been previously serviced with low quality aftermarket parts.
Laserjet 5000 fuser installation.
Let the printer cool off for approximaty 30 min. before removing. With the back of the printer facing you, press the two tabs towards the center to open the rear door.
Pinch the plastic support strap located on the left side. Squeeze the tab while pulling up to remove the support strap. This will take a little wiggling and tugging to get the strap out.
Slide the door to the left to remove it. Rember that when you re-install the door to insert the pin on the left side of the cover first.
Remove the two screws circled in red below. Use a small flat blade screwdriver at the red rectangle (below) to slightly lift the fuser. This will disangage it from its seated position. Pull the fuser out by holding on to the two green handles. You will need to tug harder on the left side because the fuser's power connection is located on its far left.
Be very careful when handling the replacement fuser. The laserjet 5000 fuser has a long ceramic heating element that will crack if you bang the fuser around or twist its frame. Please handle the fuser carefully.
Install the replacement fuser and reassemble the back panel.
Contents
What is included in a Printertechs Laserjet 5000 maintenance kit?
Fuser installation.
Transfer roller installation.
Tray 1 (Multi-purpose tray) pick-up roller and separation pad.
250 sheet tray pick-up rollers and separation pad.
500 sheet tray pick-up and separation rollers.
To purchase an HP Laserjet 5000 maintenance kit click here.
For HP laserjets 5000, 5000N, 5000DN, 5000GN, Hewlett Packard recommends the installation of a maintenance kit after every 150,000 pages printed. This is a rough estimate and you may need to install a maintenance kit far sooner than that depending on printing conditions and if the printer has been previously serviced with low quality aftermarket parts.
Laserjet 5000 transfer roller installation.
Open the top cover and remove the toner cartridge. Flip up the metal plate with the green handle circled below.
Remove the two screws circled below and remove the metal plate.
The right side of the transfer roller is held in place by a black plastic hinged clip. Notice how it is installed so you remember how to replace it. Pry it off with your finger.
Below is a picture of with the clip removed.
Use the small blue plastic transfer roller removal tool that came with your printer or use your fingers to pry up the left side of the transfer roller. Then remove the right side of the roller from its mount.
Install the new transfer roller being careful not to touch the rubber surface. Skin oils can affect print quality. Reinstall everything you have removed.
Contents
What is included in a Printertechs Laserjet 5000 maintenance kit?
Fuser installation.
Transfer roller installation.
Tray 1 (Multi-purpose tray) pick-up roller and separation pad.
250 sheet tray pick-up rollers and separation pad.
500 sheet tray pick-up and separation rollers.
HP Laserjet 5000 Tray 1 Pick-up Roller and Separation Pad Installation
To purchase an HP Laserjet 5000 maintenance kit click here.
For HP laserjets 5000, 5000N, 5000DN, 5000GN, Hewlett Packard recommends the installation of a maintenance kit after every 150,000 pages printed. This is a rough estimate and you may need to install a maintenance kit far sooner than that depending on printing conditions and if the printer has been previously serviced with low quality aftermarket parts.
Laserjet 5000 Tray 1 Pick-up roller installation.
Open the top cover and remove the toner cartridge. Flip up the green handle of the registration assembly pictured below.
Squeeze the pick-up roller and slide it to the right.
The roller is sandwiched between two black discs. Slide the roller back to the left so it is centered between the discs and pull the roller straight up and out.
Before replacing the transfer roller, replace the separation pad.
Laserjet 5000 Tray 1 separation pad installation.
Remove the front tray to make getting at the separation pad easier. Fold down the front tray and unclip it at the two points circled below.
Flip the inner tray up and the outer tray will come off by sliding it to the right. Remove the inner tray by letting it rotate all of the way down. It should fall right out of its pivot/hinge.
Use a small flathead screwdriver to pry out the separation pad. With your other hand inside the printer, remove the pad. Firmly press the new separation pad (silver edge forward) in its holder and press down until it clicks into place.
Install the new pick-up roller by making sure the thumb grip is on the left. You can only install the roller one way, so flip it around if you think you have it backwards. Slide the roller to the right until it is seated against the right black plastic disc. You might have to slightly lift and wiggle the roller to get it seated. Now slide the right disc and the roller all of the way to the left until it clicks into place.
Contents
What is included in a Printertechs Laserjet 5000 maintenance kit?
Fuser installation.
Transfer roller installation.
Tray 1 (Multi-purpose tray) pick-up roller and separation pad.
250 sheet tray pick-up rollers and separation pad.
500 sheet tray pick-up and separation rollers.
HP Laserjet 5000 250 Sheet Tray Pick-up Roller and Separation Pad Installation
To purchase an HP Laserjet 5000 maintenance kit click here.
For HP laserjets 5000, 5000N, 5000DN, 5000GN, Hewlett Packard recommends the installation of a maintenance kit after every 150,000 pages printed. This is a rough estimate and you may need to install a maintenance kit far sooner than that depending on printing conditions and if the printer has been previously serviced with low quality aftermarket parts.
Laserjet 5000 - 250 sheet tray pick-up roller and separation pad installation.
This procedure pertains to all 250 sheet trays installed in the printer. Remove the 250 sheet tray(s). The pick-up roller is located up and inside the printer. Press the white tab circled below on the white disc. This will allow you to slide the pick-up roller and the white disc to the right.
Now slide the roller back to the left so it is centered between the two white discs. Rotate the roller 180 degrees and it will drop down.
To install the replacement roller make sure the pin on the roller circled below is on the right. Rotate the roller 180 degrees so the rubber is facing up. Slide the white disc back toward the center and make sure the roller is seated.
The separation pad is located in the tray. Remove the tray from the printer, flip the tray over and you will see two black tabs holding the pad in place. Pinch the tabs and replace the pad.
Contents
What is included in a Printertechs Laserjet 5000 maintenance kit?
Fuser installation.
Transfer roller installation.
Tray 1 (Multi-purpose tray) pick-up roller and separation pad.
250 sheet tray pick-up rollers and separation pad.
500 sheet tray pick-up and separation rollers.
HP Laserjet 5000 500 Sheet Tray Pickup, Feed, and Separation Rollers
To purchase an HP Laserjet 5000 maintenance kit click here.
For HP laserjets 5000, 5000N, 5000DN, 5000GN, Hewlett Packard recommends the installation of a maintenance kit after every 150,000 pages printed. This is a rough estimate and you may need to install a maintenance kit far sooner than that depending on printing conditions and if the printer has been previously serviced with low quality aftermarket parts.
Laserjet 5000 - 500 sheet tray pick-up, feed, and separation rollers.
Remove the printer from the 500 sheet lower cassette, this will make installation much easier. Remove the tray from the cassette and flip the cassette on its side. Remove the feed roller circled below by pinching the tab at the center of the roller and pulling it off the shaft. Replace it with a new roller.
Now replace the pickup rollers. Remove them by pressing on the locking tab circled below, rotate the shaft, and pull the roller straight off. Install the new rollers.
The separation rollers is replaced by opening the hinged door and pulling the roller off of the shaft.
Reset
the maintenance count on an HP Laserjet 4000, 4050, 4100, 5000
"The
Short Cut Method"
1. Turn the printer off.
2. Hold
down the [Item-] and [Value-] keys.
3. Turn the printer on.
4.
Wait for RESET MAINTENANCE COUNT to be displayed and then release
both keys.
NOTE: Some versions of the 4000, 4050, 4100,
and 5000 will NOT have their maintenance count reset by following the
preceding "short cut" method. This is do to the many
different formatter board revisions. If the short cut method doesn't
reset the maintenance count then you will need to go
into service mode
to manually reset the maintenance count to zero.
Contents
What is included in a Printertechs Laserjet 5000 maintenance kit?
Fuser installation.
Transfer roller installation.
Tray 1 (Multi-purpose tray) pick-up roller and separation pad.
250 sheet tray pick-up rollers and separation pad.
500 sheet tray pick-up and separation rollers.
IMPRESORA HP LASERJET P3005DN (Q7815A) ESPECIFICACIONES VELOCIDAD DE IMPRESIÓN
LASERJET 4200 SERIES LASERJET 4200 SERIES EXTERNAL COVERS
LASERJET 4700 PRINTER CARTRIDGE CHECKOUT SIGN FOR EACH
Tags: series, maintenance, c411069006, installation, laserjet, instructions